Frame number needed for Lexus RS200

[stidnam]

Hi

Trying to price some parts for the 3sge beams from the Lexus RS200 and the parts guy needs a frame and model number for the EPC. Does anyone have these on hand say from a half cut??

Thanks
Stidnam

[rob]

my god toyota parts ppl are retarded

list the parts here, lots of ppl have the toyota EPC at home, someone should be able to give you part numbers then you can give them to the toyota guys

or try James ( i think its james) at castle hill toyota, it doesnt matter where u are located in NSW he will post the parts to u

[horse]

definitely post the parts you are after here. or tell him its an sxe10. if that doesnt help him then he's just retarded

[The Real Roadrunner]

dont ask for lexus as its classified a toyota in japan.

have EPC with current stuff on it (all 18gig of it)
dont expect me to look it up in 5 mins but i will get to it within 24hrs


cheers
linden

[stidnam]

Thanks guys I am after part numbers of the following off the RS200 3sge.

3sge rwd sump + the alloy bit that the sump bolts to which in turn bolts to the bottom of the block.

3sge rwd oil pickup

I am about to convert a 3sgte to rwd as I've just bought a halfcut so I want to see how much going this way would cost. I know about the 2s sump and oil pickup which will work but the baffling is apparently crap.

[tin can]

alloy sump 12101-88570 $720 est list part out of syd
steel pab 12102-88570 $332 est list part out of syd
pick up 15104-88571 $74 est list part out of syd
gasket for above 15149-88460 $7 est list part out of japan

hope this helps

[MWP]

For a 3SGE SXE10 (Altezza)...

The alloy section: 12101-88570
The steel lower pan: 12102-88570
Pickup: 15104-88571

The full 18GB Toyota EPC covering up to 2003 can be downloaded here:
http://www.phatg20.net/index.php?opt...c=select&id=86

[edit]
Doh, 3 mins too late.

[Celica RA45]

dont for get the windage tray and the hex head screws that you need as well plus the bolts are 12 mm heads for the alloy pan as well.
might not fit up to a gen 2 block with out some modifications

[tin can]

windage tray 12121-88571 ex japan est list $61.50
windage bolts 91621-j0612 x8 syd stock est $0.90
bolts for alloy sump 90901-10004x10 bris stock est list $2.75
studs for above 90116-06079x2 syd stock est list $1.30
nuts for above 90179-06299x2 syd stock est list $1.00
dowels for above 90253-13004x2 bris stock est list 2.25
bolts for steel piece 90119-06624x14 syd stock est list 1.50
studs for above 90116-06127x2 syd stock est list 1.20
nuts for above 90179-06257x2 syd stock est list 1.15


thanks
jess

[The Real Roadrunner]

might not fit up to a gen 2 block with out some modifications

tested and its more like won't unless your prepare to redrill a shiteload of holes and change the front timing cover also.

cheers
linden

[stidnam]

might not fit up to a gen 2 block with out some modifications

Thanks for all the replies. Its a gen 3 block so not too sure on how different it is to the gen 2 block.

Based on the price though I am not sure that I can justify it.

[Celica RA45]

you would be better to get the last 5sge oil pump with crank shaft angle sensor and use the 2 s steel sump
i have done a few baffled sumps for a 3sge powered clubman that racers down here and motor hasnt had a problem and he runs it on slicks and does 1.42 at the island wet sumped